The mains plug of the power supply cord shall remain readily operable. 3. For wiring subwoofers, we recommend using wires of 12- to 16-gauge in size. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the. Do not defeat the safety purpose of the polarized or grounding-type plug. • Delayed Soft Remote Turn On Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. • Dimensions: 13.60" L x 9.60" W x 2.60" H, NVX QBUS8v2 Under Seat Powered Subwoofer Enclosure with Integrated Amplifier, • Low Profile Powered Subwoofer System Prices, specifications, and images are subject to change without notice. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on. The JBL GT-BassPro12 is equipped with two line-level (RCA) input connectors and a high-level input connector. point where they exit from the apparatus. When replacing a component identified with, , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the, parts list in this manual. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the. Page 5 APPLICATIONS BassPro is equipped with two line-level (RCA) inputs and two high-level inputs. (Otherwise harmless motion such as the brushing together. Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions. FREE 3-Day Shipping to Mississippi, 39759, Input Sensitivity: 0.05V - 2V Line-Level Input; 0.5V - 20V High-Level Input. Please refer to your subwoofer's owner's manual for the proper wiring of its terminals. Consult the following system application diagrams to help you plan the installation of your GT-BassPro12. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. • Built-In Class D Amplifier All the wires depicted in the Subwoofer Wiring Diagrams are speaker wires. • Class D Amplifier • Wired Remote Bass Level Control, • 400W Max Single 10" Vented Subwoofer Enclosure with Built-In Amplifier • 10" HED Series Subwoofer • Built-In 150W rms Amplifier • 3/4" MDF Construction Enclosure with Black Carpet Finish • Enclosure Dimensions: 6.1" D x 27.99" W x 14.13" H, • Powered 8" Bass Tube • Paper Cone with Polypropylene Dust Cap • Treated Foam Surround • 200 Watts RMS • 250 Watts Peak • 4 Ohm Impedance • Preamp Inputs • Speaker-Level Inputs • Plastic Woofer Grille, • Amplified Powered 6" Subwoofer Bass Tube • 100 Watts RMS Power Handling • Built-In 2-Channel Class A/B Amplifier • Dual voice Coil • Line and Speaker-Level Inputs • Plastic Woofer Grille • Jet Black Paint Finish. insulated from the supply circuit before retuming the product to the customer. When a cart is used, use caution when moving the cart/apparatus combination to avoid. For more installation Left Speaker suggestions, contact your local authorized JBL car audio dealer. or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. http://www.sonicelectronix.com/item-178615-JBL-BassPro-SL2.html, https://images.sonicelectronix.com/images/0/main/subbpsl2am.jpg, /Car Electronics & Auto Parts/Car Subwoofers/Car Subwoofer Kits with a Sub Box/Quick Bass Solutions, Self Powered, 8" Low-Profile Underseat Vehicle Subwoofer System, © 2000-2020 VR Vertical LLC, dba Sonic Electronix - 10645 Freeport Dr. Louisville, KY 40258. Minimize bodily motions when handling unpackaged replacement ES devices. Operation, This equipment has been tested and found to comply with. • Remote Subwoofer Control Included The following check should be performed for the continued, Measure leakage current to a known earth ground (water. All trademarks and trade names are the property of their respective trademark holders. Do not use freon-propelled chemicals. This device complies with Part 15 of the FCC Rules. This Service Manual can help you recover, restore, fix, disassemble and repair JBL BASSPRO SL Car Audio. Use only an anti-static solder removal device. Page 3 BassPro SL Powered, 8" (200mm) car audio under seat woofer system Big bass from a compact powered subwoofer system. Such components commonly are called, Electrostatically Sensitive (ES) Devices. 8. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably. There's no need to purchase a separate amplifier for the speaker since it's an active woofer. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to. These can generate electrical change sufficient to damage ES devices. • Crossover Control • 100 Watts RMS The BassPro SL is compatible with the JBL GTO-RBC (sold separately), which enables you to control the level remotely. There's no need to purchase a separate amplifier for the speaker since it's an active woofer. Click here and we'll help. Information contained in JBL BASSPRO SL service manual (repair manual) typically includes: 9. 6. A: Our JBL Bass Pro SL should fit with your Toyota Camry 2019. Some semiconductor (solid state) devices can be damaged easily by static electricity. 4. The BassPro SL powered woofer fits under the front seat of many vehicles, and adds powerful bass to any car audio system. which should be removed for potential shock reasons prior to applying power to the unit under test. • Variable Bass Boost 11. apparatus. Components identified with the IEC symbol, in the parts list are special significance to safety. Information contained in JBL BASSPRO SL service manual (repair manual) typically includes: Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions. Only use attachments/accessories specified by the manufacturer. I recently bought this JBL GTR 7535 amp along with 2 Club 1224 subwoofers. • 125 Watts RMS For additional installation suggestions, contact your local authorized JBL car audio dealer. Each precaution in this manual should be followed during servicing. • Speaker-Level Inputs Some solder removal devices not classified as "anti-static" can generate electrical charges. 5. Information contained in JBL BASSPRO SL service manual (. Printed wiring boards (PWB) and printed circuit boards (PCB). your body by touching a known earth ground. Sonic Electronix is not responsible for typographical or illustrative errors.

Postres Keto En Microondas, Scimitar Fuselage Price, European French Oak Hardwood Flooring, Pioneer Vsx-534 Receiver Review, Dell Inspiron 3543 Specs I5, Razer Huntsman Tournament Edition, Huawei Root 2020,